Aiou Workshop 5403| Test 4 admin 4 years ago Spread the love /100 99 Aiou Workshop 5403| Test 4 1 / 100 1) The second layer of OSI model is a) transport layer b) Session layer c) Data link layer d) Presentation layer 2 / 100 2) The signals produced by a computer to send over phone line must be converted to: a) Low b) High c) Analog d) Digital 3 / 100 3) The diameter of fiber optical cable is: a) 62.5 mm b) 62.5 microns c) 62.5 m d) 62.5 cm 4 / 100 4) A computer network must contain at least number of computers: a) Two b) Three c) Four d) One 5 / 100 5) Cabling on a linear bus topology can be extended using which of following? a) Terminator b) Barrel Connector c) Network adapter card d) Medium attachment 6 / 100 6) Transmission from a satellite to its earth-based station is called: a) Uplink b) Downlink c) Geolink d) Baselink 7 / 100 7) Which kind of signal is mostly required by telephone lines? a) Analog b) Low c) High d) Digital 8 / 100 8) A type of communication that sends data using flow control to synchronize data between sender a) Isochronous b) Synchronous transmission c) .2 d) Asynchronous transmission 9 / 100 9) FTP facility is used to: a) File Transfer b) Check PC c) Transfer protocol d) Connect to internet 10 / 100 10) Computer networks are the convergence of two important technologies a) Computing and electrical b) Computing and Mechanical c) Computing and telecommunication d) Computing and mechatronics 11 / 100 11) Which of the following converts digital signals to analog and analog to digital? a) Repeater b) Modem c) . Multiplexer d) . Codec 12 / 100 12) Ethernet, Token bus and Token Ring have been defined by: a) Microsoft b) CCIT c) ISO d) IEEE 13 / 100 13) In _________topology, the entire network goes down if the backbone cable fails a) Bus b) Mesh c) Tree d) Ring 14 / 100 14) All of the following are elements of data communication system EXCEPT: a) Sender b) Voltage c) Medium d) Receiver 15 / 100 15) Analog signal is measured in: a) Amplitude b) Volt c) WATTS d) Hertz 16 / 100 16) How many devices can exist between a sending and receiving host? a) 10 b) 1 c) 2 d) Any. 17 / 100 17) What is another term for unguided media? a) Infrared b) Unbounded c) Wire. d) Radiated 18 / 100 18) Which value in start bit indicates that the transmission line is idle? a) .3 b) .1 c) .2 d) .4 19 / 100 19) Which one is NOT a De-jure standard? a) SNA b) IEEE c) ISO d) ANSI 20 / 100 20) The network that connects different campuses of a college in city is an example of: a) NAN b) LAN c) MAN d) WAN 21 / 100 21) The’transmission in which data can be received and. sent simultaneously is called: a) Half-duplex b) Full-duplex c) Simplex d) Duplex 22 / 100 22) The number of times a wave repeats during a specific time interval is called a) Phase b) Frequency c) Amplitude d) Frequency 23 / 100 23) An advantage of synchronous over asynchronous transmission is: a) Error checking b) Two-way c) Speed d) Simplicity 24 / 100 24) A set collection of a large number of computers all over the world connected to one another is a) Interlink b) Internet 25 / 100 25) Which problem occurs when two workstations on shared Ethernet try to access LAN at the same time a) Accident b) Collision c) Deadlock d) Termination 26 / 100 26) Which modem is used to transmit data signals through air instead of cable? a) Internal b) All c) Wireless d) External 27 / 100 27) Each set of bit pattern is called: a) Coding b) Unicode c) ASCII d) Code 28 / 100 28) What type of network is the Internet? a) WAN b) NAN c) LAN d) MAN 29 / 100 29) Which of the following is an internet protocol? a) Ethernet b) ARCnet c) Token Ring d) TCP/IP 30 / 100 30) The process of transferring data electronically from one place to another is caled a) Data Sequence b) Data communication c) NIC d) Data processing 31 / 100 31) The primary difference between a LAN and a WAN is: a) Distance b) The number of hardware devices c) The number of software programs available d) The variety of hardware devices 32 / 100 32) Which of the following is not a:data communication mode? a) Auto. b) Full-duplex. c) Simplex Half-duplex d) Half-duplex 33 / 100 33) Full-duplex communication is made. possible by the.devices known as: a) .Mouse b) ..Keyboard. c) Multiplexer: d) Modem 34 / 100 34) The process of transferring a file from remote computer to local computer on network is called a) Uploaading b) Sharing c) Downloading d) Pasting 35 / 100 35) Which of the following coding schemes uses 4-bit code? a) ASCII. b) EBCDIC c) BCD d) Unicode 36 / 100 36) Internet surfing is an example of: a) Frequency b) Half duplex transmission c) .Full duplex transmission d) Duplex transmission. 37 / 100 37) Which network covers a large area: a) WAN b) NAN c) MAN d) LAN 38 / 100 38) Which of the following topologies uses routers? a) Tree b) star c) bus d) Mesh 39 / 100 39) De Jure means a) By fact b) By chance c) By law d) By luck 40 / 100 40) The medium in which signals travel through a cable or wire is called: a) International medias b) Unguided media c) Guided media d) Local media 41 / 100 41) What binary bits are used to encode digital data? a) .0 to 9 b) Os c) 1s d) Os and 1s. 42 / 100 42) A collection of related web pages is called: a) Uploading b) Downloading c) Web Pages d) Linking 43 / 100 43) Which multiplexing technique shifts each signal to a different carrier frequency? a) DFM b) TDM c) TTD d) FDM 44 / 100 44) Which of the following features is provided with a modem? a) Self-testing b) Transmission rate c) All d) Speeds 45 / 100 45) Digital signals are commonly known as: a) Narrowband b) Baseband c) Band d) Broadband 46 / 100 46) A network that transmits data over citywide distance faster than LAN is: a) NAN b) LAN c) WAN d) MAN 47 / 100 47) NIC stands for: a) Networking Internet Connection b) Network Internal Card c) Network Interface Card d) Newer Industrial Computer 48 / 100 48) Which medium transmits voice and data via air as high-frequency radio waves? a) Fiber-optic cable b) Coaxial cable c) Microwave d) Twisted pair 49 / 100 49) Terminal is a: a) Point where data leaves the computer b) Any input/output device c) Device to give power to computer d) The last instruction in a program 50 / 100 50) A lab with twenty computers and a laser printer is an example_____ of area network a) Little b) Local c) Line d) Limited 51 / 100 51) Which of the following can severally affect the quality of satellite transmission? a) Mountains b) Light rays c) Moon d) Bad weather 52 / 100 52) The set of rules to exchange data in a communications network is called: a) Method b) Token c) Protocol d) Procedure 53 / 100 53) Which of the following is NOT a benefit of computer networks? a) Produce high quality programs b) Reduce hardware costs c) Connect people d) Enable shared applications 54 / 100 54) Which of the following is NOT a type of protocol? a) FTP b) Ethernet c) ARCnet d) CCIT 55 / 100 55) 50.This type of transmission is sometimes called start/stop transmission a) Synchronous b) Parallel c) Isochronous d) .Asynchronous 56 / 100 56) A LAN protocol in which all computers and devices on the network pass a special signal known as: a) TCP/IP b) Ethernet c) ARCnet d) Token 57 / 100 57) Sound,light and radio waves are examples of a) Pulse b) Green c) Analog d) Digital 58 / 100 58) A device that connect multiple network using similar or different protocol is: a) Ethernet b) Modem c) Router d) LAN 59 / 100 59) Which of the following consists of two insulated copper wires twisted together? a) Submarine b) Fiber optic c) Twisted-pair wire d) Coaxial cables 60 / 100 60) A type of communication that sends that uses a clock to control timing of bits being sent is called: a) Synchronous transmission b) Asynchronous transmission c) Monochronous transmission d) Isochronous transmission 61 / 100 61) How many pairs of computers can simultaneously communicate on Ethernet LAN? a) Multiple b) 3 c) 1 d) 2 62 / 100 62) Which type of data consists of words,sentences and paragraphs? a) Audio b) Video c) Numeric d) Text. 63 / 100 63) The layer that is concerned with addressing and routing is called: a) Network b) Presentation c) transport d) Physical 64 / 100 64) Transmission media are usually categorized as_ a) Baseband and broadband b) Fixed or unfixed c) Guided or unguided d) Good and bad 65 / 100 65) Which of the following is NOT a network topology? a) Band b) Star c) Bus d) Tree 66 / 100 66) A network that places all nodes on a single cable is called: a) none of these b) Tree c) Bus d) Mesh 67 / 100 67) A device that is used to connect two computers using telephone line is called: a) Modem b) Graphic Card c) Sound Card d) Ethernet Card 68 / 100 68) Which LAN access method resolves the contention between two or more nodes by collision detection a) CSMA/CS b) CSMA/CD c) CSMA/DR d) CSMA/CR 69 / 100 69) Which is the most common LAN topology? a) Star b) Mesh c) Tree d) Bus 70 / 100 70) The electromagnetic or light waves representing data are called: a) Signal b) Coding c) Information d) Mode 71 / 100 71) FDDI is a __________network. a) Star b) Ring c) Tree d) Mesh 72 / 100 72) The layer that is in between of session and application layer is a) Session layer b) presentation layer c) transport layer d) physical layer 73 / 100 73) A device used to connect similar networks is called: a) Bus b) Gateway c) All d) Bridge 74 / 100 74) Which of the following is a De Facto standard? a) SNA b) ANSI c) ISO d) ASCII 75 / 100 75) Mobile phone(Cellular) systems often use: a) MAN b) NAN c) LAN d) WAN 76 / 100 76) Which of the following is NOT a category of network? a) MAN b) NAN c) LAN d) WAN 77 / 100 77) Data link have two separate sub-layers known as: a) LLC and MAC b) TOKEN and RING c) Ethernet d) CS And MA 78 / 100 78) NIC allows direct connection to: a) Modem b) Moniter c) Printer d) Network 79 / 100 79) A network that covers a large geographic distance such as a country is called a: a) LAN b) WAN c) PAN d) MAN 80 / 100 80) The communication channels can be divided into_categories: a) Two b) Seven c) Eight d) Four 81 / 100 81) Which of the following code can represent up to 65,536 symbols? a) Unicode b) EBCDIC c) ASCII d) BCD 82 / 100 82) A modem allows computers to access other computers through following types of connection a) Wireless b) Cable c) Phone lines d) Offline 83 / 100 83) Project 802 defines standard for which layers of the OSI model: a) Physical & data link layers b) d. Network & data link layers c) c. Transport & network layers d) Physical & session layers 84 / 100 84) BCD code is a_ a) .8. b) 32 c) 15 d) 4. 85 / 100 85) Which of following protocols are properly researched, designed and finally published as a standard? a) CCIT b) De jure c) ISO d) De facto 86 / 100 86) The mode that is like a two way street with traffic flowing in both direction at the.same time is ca a) Duplex transmission b) Simplex transmission c) Half Duplex transmission d) Full Duplex transmission 87 / 100 87) signal is a continuous electrical signal in the form of wave. a) Red b) Digital c) Analog d) Green 88 / 100 88) The most commonly used LAN protocol is: a) Ethernet b) ARCnet c) WiMax d) Token Ring 89 / 100 89) DSL stands for a) Distance Server Line b) Domain System Line c) Digital Subscriber Link d) Digital subscriber Line 90 / 100 90) The music and speech.represent: a) Text b) Audio c) Image d) Numeric 91 / 100 91) The height of wave within a given period of time is known as: a) Phase b) Frequency c) Pulse d) Amplitude 92 / 100 92) One or more computers connected to a hub is called: a) Band network b) Ring network c) Star Network d) Bus Network 93 / 100 93) What layer of OSI models performs data compression? a) Presentation layer b) Physical layer c) Transport layer d) Session layer 94 / 100 94) Which communications medium requires line-of-sight? a) Fiber optic. b) Twisted pair c) Coaxial d) Microwavec. 95 / 100 95) How many characters ASCII 7-bit code can represent? a) 128 b) 500 c) 364 d) 256 96 / 100 96) The process of converting analog to digital signal is known as: a) Modulation b) Merging c) Demodulation d) Data sequencing 97 / 100 97) Typically, data transfer rate in LAN are of the order of: a) Megabit persecond b) Bits per second c) KiloBIt per second d) Terabit per second 98 / 100 98) The layer is used to control how a bit-streams of data is sent and received over physical medium a) transport layer b) Session layer c) Physical layer d) Presentation layer 99 / 100 99) The types.of signals can be: a) Digital and Analog b) Analog c) Digital d) Analog 100 / 100 100) Digital signal represents a sequence of values. a) Discrete b) Continuous. c) Unique d) Bytes Your score is LinkedIn Facebook Twitter VKontakte {{#message}}{{{message}}}{{/message}}{{^message}}Your submission failed. The server responded with {{status_text}} (code {{status_code}}). Please contact the developer of this form processor to improve this message. Learn More{{/message}}{{#message}}{{{message}}}{{/message}}{{^message}}It appears your submission was successful. Even though the server responded OK, it is possible the submission was not processed. Please contact the developer of this form processor to improve this message. Learn More{{/message}}Submitting…